How do you splice a dog fence?
When splicing the dog fence wire, all you need to do is twist the two exposed ends together, insert them into the gel-filled capsule and close the splice lock. The cylinder of the underground wire splice contains a mixture of silicone and grease, which helps to secure the waterproof connection.
What does the twisted wire do for dog fence?
The twisted wire carries the signal from your transmitter box out to the main loop but stays neutral and allows your dog to cross over without correction (without the twisted wire your dog would not be able to cross the line that runs from your transmitter out to the boundary loop).
Can invisible fence be spliced?
The Splice Kit includes: You can easily repair any wire break in your Invisible Fence® Brand outdoor pet protection system.
Can an electric fence be spliced?
Splices are required on electric fencing for two reasons. The main reason you need to make polywire splices is to extend a fence’s length. Without splicing, you won’t be able to entirely protect and seal off a paddock.
Why is my electric dog fence not working?
If your Invisible Fence control panel is beeping with a lengthy pause between each beep, it’s possible your backup battery unit needs to be replaced. Your fence will still work, but if your power goes out, the system will no longer be operational until power is restored.
How do you connect two pieces of electric fence?
Tie and join your polywire, braid or tape Take both ends of the break in your electric fence wire or tape and tie them together as securely as you can, leaving just over an inch or about 4 centimetres of excess wire or tape on both sides.
Can electric fence wires touch each other?
Wires tend to flip due to the wind. Many people tend to install in-line strainers above each other, but this is not the right way to do it. You should separate them by a fence post so that they don’t catch on each other.
Can you tie electric fence rope together?
You actually need to burn the ends of the polywire to expose the wires, then tie a knot further down the polywire, and join the two sets of exposed wires by twisting them. This makes a connection that is both physically and electrically sound.
How do you cancel out parts of underground fence for dogs?
The only way to cancel the signal in a certain area of the Boundary Area is to install a Double Loop Layout (FIGURE 2F) and twist the two parallel boundary wires together in the area where you need the the signal to be cancelled.
How do you cover spliced wires?
Cut a piece of heat shrink to cover the exposed wires. Slide the heat shrink through one of the wires. Make sure to slide the heat shrink away from area where you are splicing. Face the wire terminals toward each other and touch the exposed ends together.
What is weatherproof cable?
Waterproof cables or water-resistant cables typically come in multi-conductor constructions, designed for wet or aquatic applications.
Does invisible fence have to be a closed loop?
Yes, in order for the invisible fence to work, it needs to be a completely closed loop. There are a few other variables to watch out for, too. One of the first things you should do when installing an invisible fence is to mark out where your utility lines are located.
Can you put underground dog fence in conduit?
Yes, in-ground dog fence wire can go through conduit as long as you don’t bury it greater than 6 inches below the soil and no less than a few inches under the driveway or sidewalk.
What is a fence stretcher?
Fence stretchers are used to provide the proper amount of tension on wire fences. A tight fence protects livestock and wildlife from getting tangled in the fence which could cause injury or even death. Wire stretchers tighten wires to prevent sagging.
How do you find break in petsafe wire?
Locate the break Strip 3/8 inch off the ends the wires, then insert and twist the stripped test wire with one of the stripped boundary wires into the wire cap. Plug in the base unit and check the loop indicator light. ON: The break is likely in the other half of the boundary wire.
How do I find a break in a wire underground?
If the electrical line is buried, dig at the half-way point. Use a voltage proximity detector or attach a voltage tester to the wire and test for voltage. If no voltage is read, the break is between the source and the half-way mark. Repeat testing by moving a few feet closer to the source until voltage is found.
What is electric fence Polywire?
Poly fencing is commonly used for temporary fencing and includes polywire, polyrope (or braid), and polytape. Constructed of a combination of metal and plastic filaments, poly fencing consists of small wire strands which serve as the conductors.
How do you reset an electric dog fence?
Plug in the transmitter. The system and transmitter should reset automatically upon being plugged back in. Wait for a few seconds and look for any abnormality in the lights.
What does blinking green light mean on Invisible Fence?
When you first insert the battery into your receiver, the status light will flash green. This indicates that the receiver has started properly. In the event that the lights do not flash, check the battery to be sure that it has been inserted properly.
What does flashing red light mean on Invisible Fence collar?
Troubleshooting Questions. Why is my Invisible Fence collar blinking red? If you have started to see a red flashing light on your pet’s Computer Collar unit, your Power Cap battery may need to be replaced. You can order replacement batteries online, from your local dealer, or by calling 1-800-824-3647.
