How do you use barbed wire fence pliers?
You can use the fence pliers to bend heavy duty fencing wire or make wire for splicing wires. To do this, route the wire through the serrated circular grip on the head of the pliers and bend it over to make a loop. Then use a pair of regular pliers to twist the tail of the loop around the wire.
How do you tighten a barbed wire without cutting it?
If you’re using pliers to tighten your fence, simply grab a section of the loose fencing (between the barbs) and twist the wire 90 degrees. This should make a “z”-shaped dent in your wire, which will add tension to your wire. Continue this process along the length of the wire until it is taught once again.
Do fencing pliers cut barbed wire?
Cut wire with fencing pliers to make a barbed wire or electric wire fence. There is a wire cutter deep inside the jaws of the pliers that will cut from either side. Fencing pliers will also grip wire in the wide teeth on the end of the jaws to twist into loops for attaching spring electric wire gates.
Do I need fencing pliers?
Fencing pliers are designed to provide every function necessary for erecting or repairing a fence. The striking area on the front of the head hammers staples into wooden posts. At the other end, a curved claw can lever out even well-embedded staples.
What is a fence stretcher?
Fence stretchers are used to provide the proper amount of tension on wire fences. A tight fence protects livestock and wildlife from getting tangled in the fence which could cause injury or even death. Wire stretchers tighten wires to prevent sagging.
What is a wire strainer?
Wire tighteners, also referred to as in-line strainers, wire strainers, and strainer ratchets. They are used to keep your fence wire tight. This is done via re-tightening the tension of the wire whenever it becomes slack.
How tight should barbed wire be?
Tension. “You want it tight and straight between posts, with no droops, but not so tight that it vibrates when you hit it, like when sinking staples into the brace posts,” he says. If you’re playing a tune with your hammer, the fence is tight enough that it might break.
How do you use a barbed wire gripper?
Put the wire through the groove, and rotate the ring, so that the groove is on the opposite side of the wire. Once you start stretching the wire, the ring slides down the tapered part of the tool, and wedges against the wire for a no-slip grip, at least on barbed wire.
How do you stretch a fence with uneven ground?
If the ground is forgiving enough and the variation in the ground’s level is not too drastic, one of the best ways to install a fence over uneven ground is to dig out the fence line. Mark the fence line with string and then dig the earth away to create a fence line that is level.
What should I use to cut barbed wire?
The tool of choice for cutting the wires is, not surprisingly, a pair of sturdy wire cutters that can easily slice through the wire without much effort on your part.
Can a Leatherman cut barbed wire?
As anyone who has ever served in the military or enjoys outdoor activities will tell you, the Leatherman multi-tool should be a mandatory piece of kit. Grunts can use the pliers to extract misfires. Fishermen can remove hooks. You can cut barbed wire, crimp metal, shave tinder — you get the idea.
What tool do you use to cut wire fencing?
If you need to cut a lot of wire, general-purpose fencing pliers might not be your best bet, and it’s easier to carry a pair of small bolt cutters with you. Like the Knipex fencing cutters, which are my favorite cutting tool.
What are hog ring pliers?
Hog ring pliers are a tool used to clamp together hog rings. Hog ring pliers are a fast and easy method of attaching or connecting various materials together. These hog ring pliers are spring loaded and have groove marks on the inside of the nose to hold the hog rings in place for easy installation.
What are hammer pliers used for?
They are ideally used for bending and holding, crimping metal, looping and cutting wire and soft nails. You can use them for loosening and tightening nuts. Pliers can be used in a variety of plumbing, carpentry or electrical projects.
What are wire pliers?
Lineman’s Pliers: These instruments are used for gripping and contorting wires and cables. Typically found in electrical and lineman industries (hence the name), these types of pliers are advanced and heavy duty for professional use. Diagonal Cutting Pliers: This tool is used solely for cutting wire.
How do you stretch barbed wire to metal post?
Unroll the barbed wire along the line of the fence posts. Fasten the wire to one of the corner posts and pull it as tightly as possible to the next corner post. Use a wire stretcher, a mechanical ratchet device, to pull the wire tighter. Fasten the barbed wire to each of the metal posts along the fence line.
What are Crimp sleeves?
Basically, a crimp sleeve is a cylindrical metallic part, resembling a thimble that’s open at both ends. Bare, uninsulated wires of the same or varying gauges are inserted at the flared end, and crimped together. The crimping results in a fast connection that will not easily pull apart.
What is crimp area?
a : a section of hair artificially waved or curled. b : a succession of waves (as in wool fiber) c : a bend or crease formed in something.
How does a Gripple Plus work?
Gripple Plus® Wire Joiners Includes integrated adjustable torque setting on the handle. Once the pre-set wire tension is reached – the tool dis-engages to prevent overstraining and potential wire damage. Stainless steel springs provide excellent corrosion resistance. Long lasting and can be re-used.
How far apart should T posts be for barbed wire?
The typical spacing of posts is between 8′ and 12′. The distance should be determined by the type of fence and the amount of support that the fence needs in order to stay taught.
